NEUTRALÈNE ® N 100
SAFETY DEGREASING SOLVENT
Non-flammable, VOC-free
Readily biodegradable
Evaporates completely,
leaves no residue
Can be used cold or hot
Specially designed for parts washers
HIGH-PERFORMANCE DEGREASING SOLVENT
SPECIAL PARTS WASHERS, STRUCTURES, NETWORKS, PIPEWORK, RETENTION AREAS, INDUSTRIAL MAINTENANCE
|
|
NON-FLAMMABLE
Can be used cold or in baths up to 70°C.
Allows ATEX zone declassification.
Very high solvent power, KB value above 50.
Dielectric breakdown voltage IEC 156
50,000 volts.
Immediate dissolution of tars, crude oil, heavy hydrocarbons, combustion residues, greases and lubricants.
Specially formulated for accelerated settling in solvent parts washers.
SMP OPTIMISATION
Solvent Management Plan
(IED DIRECTIVE)
Assessment of solvent inputs and material outputs
Low volatility, reduced consumption.
ELIMINATION OF SOLVENT EMISSIONS
|
ODP 0 |
PRP 0 |
Freezing point: -20°C. Outdoor storage permitted.
Reduction of industrial risks, business interruption losses, and third-party liability
(Insurance Code)
DESCRIPTION
Non-flammable, VOC-free, biodegradable, degreasing solvent. A safe cleaning agent with high solvent power, specially developed for use in solvent parts washers. A technical fluid based on plant-derived esters of agricultural origin, it can also be used for all manual degreasing operations, with or without mechanical action, or by immersion in cold or hot baths up to 70°C.
PRECAUTIONS FOR USE
NEUTRALENE® N 100 presents no hazard, except in the highly unlikely event of accidental ingestion. Refer to the Safety Data Sheet for recommendations regarding storage, use and disposal after use.
“Dangerous. Follow the safety instructions.”
TYPICAL PHYSICOCHEMICAL PROPERTIES
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Appearence |
Visual |
Fluid |
- |
|
Colour* |
Visual |
Colourless |
- |
|
Odour |
Olfactory |
Odourless |
- |
|
Density at 25 °C |
NF EN ISO 12185 |
805 |
kg/ m³ |
|
Refractive index |
ISO 5661 |
1,4465 |
- |
|
Freezing point |
ISO 3016 |
<-20 |
°C |
|
Solubility in water |
- |
Insoluble |
% |
|
Kinematic viscosity at 40 °C |
NF EN 3104 |
2.5 |
mm²/s |
|
Acid value |
EN 14104 |
<0,1 |
mg(KOH)/g |
|
Iodine value |
NF EN 14111 |
0 |
g 2 /100g |
|
Water content |
NF ISO 6296 |
<0,001 |
% |
|
Residue after evaporation |
NF T 30-084 |
0,0 |
% |
|
Vapour pressure 20 °C |
NF EN 13016-1 |
<0,002 |
kPa |
|
PERFORMANCE PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Kauri-butanol (KB) value |
ASTM D 1133 |
53 |
- |
|
Evaporation rate |
- |
>4 |
|
|
Surface tension at 20 °C |
ISO 6295 |
28 |
Dyne/cm |
|
Dielectric breakdown voltage |
CEI.156 |
50 000 |
Volts |
|
Copper strip corrosion, 100 h at 40°C |
ISO 2160 |
1a |
Rating |
|
FIRE SAFETY PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Flash point (closed up) |
ISO 2719 |
>100 |
°C |
|
Auto-ignition temperature |
ASTM E 659 |
>230 |
°C |
|
Lower explosive limit |
NF EN 1839 |
0,6 |
% (volume) |
|
Upper explosive limit |
NF EN 1839 |
6.5 |
% (volume) |
|
Content of explosive, oxidising, flammable, highly or extremely flammable substances |
CLP Regulation |
0 |
% |
|
TOXICOLOGICAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Anisidine value |
NF ISO 6885 |
<1 |
- |
|
Peroxide value |
NF ISO 3960 |
<1 |
meq(O₂ ) /kg |
|
TOTOX (anisidine value + 2 × peroxide value) |
- |
<3 |
- |
|
CMR, irritant and corrosive substance content |
CLP Regulation |
0 |
% |
|
Residual methanol content from transesterification |
GC-MS |
0,0 |
% |
|
Emissions of hazardous, CMR, irritant and corrosive compounds |
GC-MS |
0 |
% |
|
ENVIRIONMENTAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Biodegrability |
OCDE 301 A |
>80, >90 |
% |
|
Vapour pressure at 20 °C |
- |
<0,1 |
hPa |
|
VOC (Volatile Organic Compounds) content |
- |
0 |
% |
|
Sulfur content |
GC MS |
0 |
% |
|
Benzene content |
ASTM D6229 |
0 |
% |
|
Total halogen content |
GC MS |
0 |
% |
|
Chlorinated solvent content |
- |
0 |
% |
|
Aromatic solvent content |
- |
<0,01 |
% |
|
Content of substances hazardous to the environment |
Règlement CLP |
0 |
% |
|
Content of compounds containing PRP |
- |
0 |
% |
|
Content of compounds with ODP |
- |
0 |
% |
|
Carbon footprint, life-cycle assessment |
ISO 14040 |
1,55 |
kg CO₂ equivalent |
|
ADDITIONAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Aniline point |
ASTM D 611 |
80 |
°C |
|
Bioaccumulation – n-octanol/water partition coefficient |
OCDE 107 |
<3 |
logKow |
|
Effect on water classification |
WGK |
1 |
Class |
PRESENTATIONS
|
1000 L ICB CONTAINER
|
200 L Drum
|
20 L Can
|
METHODS OF USE
 |
 |
|
Degreasing with a cloth |
Degreasing with a brush |
|
|
|
|
Low-pressure sprayers with water rinsing |
Solvent parts washers |
|
|
|
|
Ultrasonic tanks |
Hot and cold immersion tanks |
 |
 |
| Rotating or reciprocating basket | A3 washing machines |
